SGX-CA900 Update Manual

This manual is for Mac OS X. SGX-CA900(hereafter the CycloComputer) is updated using a specific PC Application. (Pioneer Cycle Cloud Connect) Firstly it is necessary to install Pioneer Cycle Cloud Connect on your PC. The following steps are required to update the CycloComputer:

  1. Install Pioneer Cycle Cloud Connect
  2. SGX-CA900 Firmware Update(Must be done on SGX-CA900)

Refer to the following for details of each step.

  • If the device is logging, stop logging and save the log data before the update.

1. Install Pioneer Cycle Cloud Connect

Outline

Install Pioneer Cycle Cloud Connect.

Explanation of Screen

Start

http://pioneer-cyclesports.com/us-en/support/products/sgx-ca900.html

Please download the executable (.pkg) file from the URL above.

Please double click the executable file after downloading.

Setup Wizard

"Welcome to Cycle Cloud Connect" will be displayed. Please click on "Continue".

Please read and agree to the License Agreement, and click on "Continue".

Please click on the "Agree" button to agree to the License Agreement.

Please Click on "Install"

Please insert the administrator account password, and click on "Install Software".

Installation has been completed once the "Install is Complete" message is shown. Please click on "Close" to terminate the Installer.

2. Update the Firmware of the SGX-CA900

Outline

Start the Firmware Manager and update the firmware of the CycloComputer

Please carry out the following operations on the CycloComputer.

Start up Update Mode on the CycloComputer

  1. If USB is connected, first disconnect the USB connector.
  2. The SETTINGS menu can be selected by pressing "SETTINGS" on the Home Screen.
  3. Please tap on "SYSTEM" then "FIRMWARE UPDATE". Messages will be shown regarding the Backup of Settings and Firmware Update.
  4. Please tap on [OK]. Backup data will be generated automatically, then Update Mode will activate.
  5. Confirm that the CycloComputer Screen is illuminated all in white.
  6. Connect the CycloComputer to the PC via USB.

If the screen is flashing, then the battery level is insufficient. Please charge sufficiently before continuing.

Please confirm that the CycloComputer is in Update Mode, then perform the following operations in Pioneer Cycle Cloud Connect.

Pioneer Cycle Cloud Connect Operation

Method of Operation

  1. Click on the Pioneer Cycle Cloud Connect Icon in the Menu Bar, select "Actiate Firmware Manager"
  2. Connect the CycloComputer, which should be in Update Mode, to the PC via USB.
  3. Follow the instructions given by the Wizard.

Firmware Update can take 20-30 minutes in a FTTH environment.

Explanation of Screen

Start

Please confirm that the PC is connected to the Internet, and the CycloComputer is connected in Update Mode to the PC.

Select "NEXT" to proceed to the Firmware Selection Screen.
Selecting "CANCEL" will cause the application to terminate.

If the Serial Number Registration Screen is shown

Please input the tewelve digit serial number shown on the CycloComputer and press "NEXT". The serial number is the twelve digit number/letter combination shown in the "S/N" Section on the back of the CycloComputer. If the Serial Number is input correctly, the Select Firmware Screen is shown.
Selecting "CANCEL" will cause the application to terminate.

Firmware Selection

Selection of Firmware

Please select the version of the firmware you wish to update. The Update History of that version will be shown.

Current Firmware Version

The Firmware Version of the currently connected CycloComputer is shown.

Selecting "NEXT" causes the Software License Agreement to be shown.
Selecting "CANCEL" will cause the application to terminate.

Software License Agreement

The Software License Agreement for the Firmware is shown. Select "AGREE" to accept to the agreement.

Selecting "NEXT" causes the Firmware Update Confirmation Screen to be shown.
Select "RETURN" to return to the Select Firmware Screen.
Selecting "CANCEL" will cause the application to terminate.

Update Confirmation

Please confirm the Current Version and Update Version of the firmware.

Select "NEXT to proceed to the Version Update Screen, wher the Update Operation will begin.
Select "RETURN" to return to the Software License Agreement Screen.
Selecting "CANCEL" will cause the application to terminate.

Firmware Update

The progress of the Version Update of the CycloComputer is shown. Once the Update is complete, the "NEXT" button will become active.

Select "NEXT to proceed to the Update Result Screen.

Update Result

The Result of the Update Operation is shown. Follow the instructions in the Dialog Window to carry out the following operations on the CycloComputer.

Please perform the following operations on the CycloComputer.
  1. With the CycloComputer still connected to the PC via USB, press the START/STOP button for five seconds or more. The CycloComputer will restart.
  2. The CycloComputer will show the Initial Settings Screen, so please select the Language. The Firmware Update will then continue.
  3. Once the CycloComputer shows the Disconnect Message, please disconnect the USB cable from the CycloComputer.
  4. The CycloComputer will show a message confirming the restoration of settings. Please select "YES".
  5. Once the Firmware Update is complete, the CycloComputer will automatically turn off.
The Update is now complete. Click on "FINISH" in the Application Screen to terminate the Firmware Manager. To repeat the Update procedure, return to Step 2. "Update the Firmware of the SGX-CA900".